Masterflex 07575-20 L / S數字處理驅動器與粉末涂層鋼外殼，0.1至600轉，115/230 VAC

Masterflex L / S數字處理驅動器與粉末涂層鋼外殼，0.1至600轉，115/230 VAC

Masterflex L/S Digital Process Drive with Powder-Coat Steel Housing, 0.1 to 600 RPM, 115/230 VAC

流體輸送，分配，實驗室和計量應用，流程和沖洗環境的理想選擇

外殼是完全密封的IP66和NEMA 4X額定

直沖式驅動器是易清潔，耐常用的清洗和消毒液，僅需要沖洗干凈

無刷免維護電機速度控制精度±0.1％，6000-1調節比

全遙控功能可簡單地集成到自動化流程

流速：0.006至3400毫升/分鐘（至54 GPH）L/S油管。流量取決于驅動器轉速和泵管尺寸。

圖形液晶顯示四種工作模式，連續運行，定時分配，復制分配量分配。

連續查看泵

菜單驅動的界面，可以選擇七種語言，編程及操作

免除：體積毫升（0.001?99999毫升），升和加侖;復制1到9,999分配周期;或SEC時間的時間間隔，每次分配周期（1秒到99小時59分59秒）

通過密封圓形連接器驅動器上遠程控制：

-可擴展速度控制輸入0至20 mA，4至20 mA或0?10 V; 

-抽水方向需要集電極開路或觸點閉合; 

--Start/stop/purge要求打開電極開路或觸點閉合; 

-轉速計輸出可擴展0至20 mA，4至20 mA，0?10 V，集電極開路

型號07575-20具有粉末涂層鋼板外殼。使用該驅動器的過程中，不銹鋼制造、水處理應用程序不是一個關鍵需求。

這些精密驅動器提供模擬遠程控制選項和簡單的編程是自動化過程應用的理想選擇。驅動器具有可編程分配區間，允許您設置延遲分配周期之間方便、自動分配。程序校準，確保分配和顯示精度驅動器每尺寸油管存儲校準值

驅動程序通過簡單的鍵盤膜，鍵盤鎖定/解鎖功能保護設置。電機是可逆的，所以您可以清除之前或之后，在任一方向的泵和泵液管

包含： 6英尺（1.8米）的線與IEC 22 320/CEE的連接器耦合器;水密線連接。插頭/電源線驅動器隨附在訂貨時指定目的地國家。

Ideal for fluid transfer, dispensing, and metering applications in laboratory, process and wash-down environments

Housings are completely sealed—IP66 and NEMA 4X rated

Washdown drive is easy-to-clean and resistant to commonly used cleaning and sanitizing solutions—simply hose down to clean

Brushless, maintenance-free motor offers ±0.1% speed control accuracy with a 6000 to 1 turndown ratio

Full remote control capabilities allow easy integration into automated processes

Flow rate: 0.006 to 3400 mL/min (up to 54 GPH) with L/S tubing. Flow rate depends on drive rpm and tubing size.

Graphical LCD shows four operating modes continuous run, timed dispense, copy dispense, volume dispense. View pump performance continually

Menu-driven interface lets you select one of seven languages for programming and operation

Dispense by: Volume—in milliliters (0.001 to 99999 mL), liters, and gallons; Copy—1 to 9,999 dispense cycles; or SEC—time interval between each dispense cycle (1 sec to 99 hr, 59 min, 59 sec)

Remote control via sealed circular connector on drive:

--Speed control input scalable 0 to 20 mA, 4 to 20 mA, or 0 to 10 V; 

--Pumping direction requires open collector or contact closure; 

--Start/stop/purge requires open collector or contact closure; 

--Tachometer output scalable 0 to 20 mA, 4 to 20 mA, or 0 to 10 V, open collector

Model 07575-20 features a powder coated steel housing. Use this drive in process, manufacturing, and water-treatment applications where stainless steel is not a critical requirement.

These precision drives offer analog remote control options and simple programming—ideal for automated process applications. Drives feature a programmable dispense interval that lets you set the delay between dispense cycles for convenient, automated dispensing. Programmed calibration ensures dispense and display accuracy—drive stores one calibration value per tubing size.

Program the drive via the simple membrane keypad; keypad lock/unlock feature protects settings. Motor is reversible so you can purge tubing before or after pumping and pump fluid in either direction.

What's Included:

Six-foot (1.8-meter) line cord with IEC 320/CEE 22 connector coupler; watertight cord connection. Specify destination country when ordering; drive is shipped with country-specific plug/cord set.